Jump to content

Frank C

Member+
  • Posts

    771
  • Joined

  • Last visited

  • Days Won

    18

Everything posted by Frank C

  1. Here’s the video from Dexter on bearing maintenance: https://youtu.be/GnH-h3W9XvI
  2. From Lowe’s, $40 for the 2” hole saw plus $18 for the pilot bit. So definitely more expensive than standard hole saws. But very nice results.
  3. That’s a big troubleshooting clue. The light and motor are wired in parallel, and share a common ground point (see schematic in previous post), so since the light didn’t work either when this jack problem occurred, that points to a wiring connection issue with either the 12v hot lead or the ground, not a motor problem or jack screw problem.
  4. It’s always a bit tense when cutting or drilling into the nice pristine glossy surface of the Ollie, you just have to make sure that the drill bit or hole saw doesn’t go skidding across the surface and create a big ugly scar, and also taking care not to crack or chip the gel coat layer. But I’ve had very good success using diamond grit hole saws on the Ollie for making holes. The diamond grit hole saw makes a very nice clean cut, and doesn’t cause any chipping or cracking of the top gel coat layer. The center pilot bit creates a nice starter hole to keep the hole saw from shifting while drilling.
  5. For reference, here’s a couple pics of what the outer Oliver hull fiberglass construction is like. I have this piece from a 2” diameter hole I cut in the lower hull for a modification I did. The total thickness in the area I cut through is about 1/4”. Some high stress areas are thicker with additional reinforcement in the fiberglass. The outer white gel coat layer is about 1/32” thick. A small pin head size ding is not a problem for an Ollie 🙂.
  6. The Progressive “LI” (Lithium) setting is the wrong voltage and charging profile for AGM batteries. Why are you leaving it set in the wrong position instead of fixing it? That is very likely the cause of your battery problems.
  7. I carry a large scissor jack (a military surplus HUMVEE jack with frame adapter, referenced in the other thread link that John posted above) and some pieces of 4”x4” lumber for raising the trailer for tire changes and wheel bearing maintenance. I lift the trailer with the scissor jack and then put the stabilizer down as a safety backup just in case. Tire chocks on the trailer wheels on the opposite side, and the trailer still hitched to my truck, so the trailer won’t shift at all while lifting. This setup has worked well and is very stable and safe when I have to work on the trailer. I prefer overkill when it comes to safety 🙂. And I don’t trust just using the stabilizers only to lift the trailer for tire changes after seeing how small the welds are on the stabilizer mounting brackets.
  8. No sensor in the wiring (see attached schematic) or mentioned in the manual anywhere. You either have a blown fuse, a faulty wire connection somewhere, or else the jack screw is binding up because of the trailer shifting. The motor may have a built in TCO (thermal cutout, often built into motor windings) to protect the motor from overheating, but no mention of that in the jack manual.
  9. Top of the ball should be about 24” +/- 1/2” from the ground to calculate your hitch drop needed. And for locking the Bulldog coupler while towing, most of us use this collar with a padlock. "The Collar" Trailer Hitch Lock... https://www.amazon.com/dp/B00HL2NM0K?ref=ppx_pop_mob_ap_share
  10. Here’s a link to the Truma site for a PDF copy. https://www.truma.net/sites/default/files/inline-files/AquaGo%20stuck%20in%20clean%20mode.pdf
  11. Did you accidentally put the Truma into Cleaning Mode? If so there’s a procedure to follow to get it out of that mode. Here’s what Truma sent me to get the unit out of cleaning mode. And note that propane should be ON when doing this process.
  12. Not sure which lithium batteries you have. I’ve been considering upgrading my lead acid wet cell batteries to lithium and have been looking at manufacturers specs. The BattleBorn lithiums state a 100% usable depth of discharge (see data sheet). The battery has its own built in battery management system to protect it from damage. I’d probably never go that low, all the way to 0%, but nice to know it’s not a problem if it ever does happen.
  13. Sorry to hear you might be having trouble with your new Ollie. Since you are a new owner, first let’s make sure you are looking at the right valve when you say it appears the handle cable isn’t connected. The gray tank DRAIN valve is under the access hatch under the street side (driver side) bed near the rear of the trailer (see photo below). It is NOT under the dinette seat. The two valves under the dinette seat closest to the bathroom are the black tank drain valve and the gray tank anti-backflow valve (prevents gray water from sloshing back up into the shower pan when traveling, activated by the pull handle near the floor by the toilet, or by the switch in the closet if you have the optional electric valve). Some owners have pulled gray tank drain handle but then looked at the valve under the dinette and wonder why the valve didn’t move. Once you confirm you are looking at the correct valve when pulling the drain handle, then it’s a pretty simple matter to see where the problem is. The cable is held into that aluminum cylinder (circled in John’s photo) by a set screw. The set screw may be loose or even missing. If missing you should be able to get a replacement at any hardware store.
  14. One of our fellow Oliver owners/forum members, Foy Sperring, makes many items for the Oliver trailers. One of the items is a kitchen drawer organizer. We have the nightstand drawer organizer and it’s been very useful. Here’s a link to his catalog: https://drive.google.com/file/d/17XFL_5ine1WusHVKYguUBRmkj2KnJUN_/view?usp=sharing
  15. Thanks for the info. But you may be overthinking it 🙂. First I assume you mean track width (side to side) and not wheelbase? Wheelbase is the distance between front and rear axle centerlines on a vehicle. Track width is the distance between the right side and left side wheels. And notice that you can use what’s referred to as the small angle approximation, where at small angles near 0 degrees, the SIN and TANGENT values are basically approximately equal to the angle, normally when the angle is measured in radians, but works close enough in degrees also with the Oliver width as the adjacent leg of the triangle, as evidenced in your chart. Even at 5 degrees, the elevation is 5.86”, only a little over a 1/2 degree of difference using the small angle approximation method, especially since the Lego type leveling blocks stack up in 1” increments. So I’ve just been using the Lego blocks as a “ degree”. I put my iPhone on the main aluminum tongue beam of the trailer at the front and use the Clinometer app. One degree out of level side to side means I will use one block, 2 degrees and I’ll use two blocks, etc. Once the trailer is leveled to within 1/2 degree that’s usually very comfortable as a “level” trailer, and is well within the limits for the absorption type refrigerators. 1/2 degree within level is waaay better than most folks that I’ve observed camping 🙂. And we are usually 1/2 a degree up at the front when camped to help drain the tanks.
  16. The tongue jack on our 2019 also has a redundant fuse.
  17. For future reference if you ever need to change that fuse, here’s a pic of the fuse holders for the three jacks (the three yellow inline fuse holders). Located under the access hatch under street side (driver’s side) bed on our 2019 Elite II. I can’t guarantee that yours will be in exactly the same place since I’m starting to think that no two Olivers are built exactly the same, especially in the early years 😂.
  18. I usually winterize in late October or early November here in our part of PA. That’s when the overnight temperatures can start getting below freezing at night. I don’t like to take any chances. There was one Oliver owner who posted a horror story here on the forum of all the damage caused to his trailer by getting caught “un-winterized” during a cold spell. It pretty much destroyed every part/component of the water system. A very expensive repair bill.
  19. I can’t wait to see the upgraded Tundar TuRD Pro off-road package with the huuuuge 14” wheel option and plastic skid plates 😂.
  20. For item #1, make sure you opened the gray tank backflow preventer valve (by pulling the handle near the floor by the toilet, or with the switch in the closet if you bought the optional auto-valve feature). For item #3, there is no manual valve for the black tank flush line. Just hook up a water hose to the flush fitting on the outside of the hull (use a dedicated hose for this, do not use your drinking water hoses) and turn on the water. Keep an eye on it though so you don’t overfill the black tank and have it overflow the toilet. The two valves under the forward dinette seat are the black tank DRAIN valve and the gray tank back flow preventer valve, both of those are remotely actuated by cables.
  21. The braided supply lines with 1/2” female pipe thread ends are available in various lengths at any hardware store like Lowe’s, etc., along with the Sharkbite fittings to go on the existing water lines on the trailer.
  22. !!!! DO NOT USE THE JACK OR JACK STAND ANYWHERE ON THE FIBERGLASS !!! The jack points are on the galvanized steel subframe at the locations indicated by the stickers. Those are the main frame rails that support the trailer. ALWAYS jack on the steel subframe.
  23. No, the bad bypass valve still felt normal when opening and closing it. The faulty seal inside the bypass valve wasn’t noticeable until I removed the valve. The new CAMCO bypass valve is installed and works well so far. One nice little detail of this CAMCO valve is that the positions are labeled (open or bypass). And I changed all water lines into and out of the Truma to braided flexible supply lines and brass fittings to eliminate the issue of breakage of the rigid plastic connections that some owners have had. Camco 37463 3-Way By-Pass Valve Replacement - Brass https://a.co/d/8qur0uz
  24. Sewer hoses store in the back bumper (one of the nice Oliver design features that you don’t find on other trailers), and that’s where the drain connection is. Most owners just leave the hose connected to the drain inside the bumper, and cap the end of the hose. I see a lot of other trailer brands with the sewer pipes and valves hanging way down below the frame, unprotected from road hazards.
  25. https://www.rigidhitch.com/media/installation_instruction/5535.pdf
×
×
  • Create New...