dewdev

I would suggest that you first go to the Oliver web site and open up a service ticket and ask the question. You can also add your photo to help with the question. Southland may be too new to help you on this issue.

1. On the bottom surface of the hatch cover over where the pump is, there should be a picture showing the valve configuations for the different uses. The pictures should also be in your Owner's manual 2. Highly unlikely. If I was you, I would check to see if all the plumbing connections are tight with no leaks and none are sucking in air. 3. Should not be a problem. All Oliver's are like that.

@John Dorrer Thanks for point that out. I checked and have had the same $3.50 charge each month starting in February. I am going to use up my balance ASAP before another charge on May 1. My understanding is the charge is not by OTT but the credit card company.

I use a 2000 watt generator (with the ground plug) and it powers up the Ollie and the AC. I do have to shut off the breaker to the inverter/charger for it to power up the AC compressor.

If you all had a compost toilet, you would not need the water pump on at all for flushing. Just making a little light of the subject. Ha Ha

Bill: I was having the same problem signing into the Rewards Section. When I tired to log in I got a "Bad Request" page.

But will the new independent service locations offer the same annual maiintenance program that OTT offered? Or put another way, will the independents even be told and trained of what OTT offered for the annual maintenance?

@ScubaRx and @SeaDawg. Since you are moderators, you may know more about the end of service at the factory then us other owners. Has OTT explained to you how OTT be training the local dealer's service personne and when? Will OTT explain the services that they offered at the factory during their annual maintenance services?

The tite say San Antonio

@Mark Meadows FYI, I see there is a dealer in Utah. Not sure if that is closer to you than Oregon. A list fo dealers is on the Oliver web site.

Can you go to one of the new Oliver authorized sales-service centers near you?

Congradulations Take you time at the factory and during your travels Stay at the Oliver Campground and checkout all equipment on the Ollie until you have run out of questions. Safe travels

@rideadeuce FYI, Your link is only for the 1/4" tubing I found the Dometic water faucet on Amazon but not the 3 gallon container you show. Can you provide a link for the container? Did the containers already have a connection for the 1/4" tubing? Thanks

@hobo Did Mike at ALCAN give you more information on why he thught the 4 spring set was "inadequate for our trailers" ? Thanks

Nice job. Looks like how I relocated/nstalled mine, thnaks to @Overland and @Mattnan and their instructions and parts list . I did not see the holes where the mount was installed before you movd it. You must have filled the holes. Now you can install a hatch into the cellar. I store my table top in the closet on the inside wall next to the head, when not in use. I use velcro to secure it to the wall.

SeaDawg: How do you get the forum members name (with blue shading) into a follow-up post, like you have in your post here? Thanks

Very Impressive RAM. I did not see any solar panels on the RAM. Where are they located on the truck?

Geronimo John: Thanks for Posting John Davies procedure.

Sorry to bring this subject up again on the forum, but I want to find out what people are using to check the level in their LP tanks and if they use a measuring device. I myself initially decided to not get anything to measure the LP level in my tanks as I can just fill up the empty tank when I switch the valve over to the 2nd tank. But I keep coming back to this subject. (MaybeI I am a little bored over the winter.) There are tank gauges that you install in-line. There are also the devices you install on the bottom of the LP tank like from Mopeka. There are also hand held measuring devices that you scribe along the side of the tank to determine where the liquid level is inside the tank, such as: 1. Dometic makes a measuring device, model GC-100, $68.99 2. Truma also makes a similiar measuring device - $74.79 So my question is regarding only the two numbered devices above. For those that have used either of the devices, did they work ok and were you happy with the devices and would you recommend for purchase? Thanks

I would suggest that only 150 lbs (including the box) be added. Same weight that OTT recommends for bikes and bike racks on the back.

Toby I also have a 2018 Elite II. My procedure may not help you. But, after the Ollie wakes up from it winter's nap, I have trouble getting the Dometic refigerator started. I usually have to play with the on-off switch button, depressing the button multiple times and sometimes just holding the button in. So far, after a little time doing this the refrigerator finally starts and the lights on the control board come on. On another subject, in the future, you might want to add your year and hull # to the signature line, so people can see what Ollie you have and can help you better.

What is the model of the PD Charger/Converter with the lithium ion charging profile with the remote display panel like you have (the drop in model you refer to)? I am guessing that you would need to buy both seperately. (I looked on the PD web site and there are a lot of different models available)

Chukarhunter: Excellant explaination that hopefully everyone on this thread reads. Obviously you must have an electrical background and/or good working electrical knowledge. As far as the PROwatt SW2000 inverter wall panel in my 2018 Elite II, I have no inverter wall panel as you have described. The only PROwatt SW2000 inverter panel on the wall in my Ollie is the picture I have posted below. Could you post a picture of your PROwatt SW2000 wall panel in your 2020 Olilie, which may help others with that vintage inverter and how you described changing settings.

@rich.dev I do not believe that for our 2018 Elite II (with my Hull 354) and Xantrex PROwatt SW2000 inverter and Wandering Sagebrush's (Hull 364) with the original Xantrex PROwatt SW2000 inverter (which he does not have now) has anyway to change the amp output. There is no Wifi type connection to that 2018 inverter to make that modification. This inverter was before Lithium batteries. If I am wrong, someone please correct me.

SeaDawg uses a 1000 watt generator to charge their batteries. a neutral ground plug is REQUIRED. I use a 2000 watt generator (with the neutral ground plug) and I can run my AC. My AC has the reduced voltage starter installed. When using my generator, I need to shut off the circuit breaker to the inverter because it takes to much power when trying to run the AC. My hull # is 10 earlier than your hull #.