Jump to content
Sign in to follow this  
tumbleweed

Rear bumper pins

Recommended Posts

I've used about 8 inches of picture frame wire to wire my bumper pins to the bolt that the bumper rotates on to so I don't lose them. Keeps them from falling in the dirt and handy when closing the bumper and doesn't seem to interfere with opening or closing it.

From a senior who forgets where he puts stuff..... :?

Share this post


Link to post
Share on other sites

Glad to hear that, Doug. The earlier models didn't have wires or chains for the pins. We used some Stainless Steel leader wire and crimp rings from the tackle box to secure our pins. Thanks for the update.

Sherry


2008 Ram 1500 4 × 4

2008 Oliver Elite, Hull #12
 

 

Share this post


Link to post
Share on other sites

Another note on the pins. The right side pin is on my rig was really tight, almost impossible to remove or insert some times. I ran a drill bit of the same size as the existing hole and it now works like a champ. This did give the pin a little more play, but it doesn't appear to be an issue.

Share this post


Link to post
Share on other sites

That's funny...my right side pin is also extremely tight. I've been able to get it out by pushing the bumper in tight with one hand while twisting the pin out with the other. I'm afraid to drill it out because I don't want to have the opposite problem...a rattling bumper. So for now, I'm leaving it as is.

 

Herm

Share this post


Link to post
Share on other sites

The reason your pins are so tight is because the spare tire cover is pressing down on the bumper and not allowing it to swing into its fully "up" position. It only takes a few thousands of misalignment to make the pins not fit well. Drilling them out is probably the only long term solution. You can, however, loosen the winged nut holding the spare tire cover on and lift the cover as much as possible and re-tighten the nut, really tight. This works, but probably only temporarily as travel will inevitably allow the cover to slip down and return to a position resting on the bumper and not allowing it to swing up fully again. You can always try slamming it into the closed position, but it makes a lot of noise when you do!

 

Steve


Steve, Tali and the dogs: Reacher, Lucy and Rocky plus our beloved Storm and Maggie (both waiting at the Rainbow Bridge) 2008 Legacy Elite I - Outlaw Oliver, HULL NUMBER: 0026 2014 Legacy Elite II - Outlaw Oliver, HULL NUMBER: 0050 2017 Silverado High Country 2500HD Diesel 4x4 

 

      ALAKAZARCACOCTDEFLGAIDILINIAKSKYLAMEMDMA       ABBCMBNSYTsm.jpg

 

 

Share this post


Link to post
Share on other sites

I've struggled all day today to remove the bumper pins and drain the grey tank. No luck.

 

Then my daughter and family arrive for a visit. He stares at the structure for about a minute and then LIFTS the bumper UP near each pin and they just slide out effortlessly.


2018 Ford F150 3.5EB 4X4 Max Towing / 2019 Oliver Elite II - Hull 421 / "Cocoon"

Share this post


Link to post
Share on other sites

[postquote quote=178842][/postquote]

 

Yep, that’s how mine come out as well.  Glad you got some family help.

 

Mike


Mike and Krunch   Lutz, FL   LEII #193 “the dog house”

 

 

Share this post


Link to post
Share on other sites

Our Oliver is one of the early ones. Hull #39. Are the pins still the same?. I have lost one and wondered where I can go to replace it. I have put a safety chain on my existing one and will do the same when I find a replacement fo the other one.

B9DF59E3-FFDD-4DC6-B24A-F68E8141488D.thumb.jpeg.328e88270f8c5b736a9ae2bd3602d369.jpeg

Share this post


Link to post
Share on other sites

I have lost one and wondered where I can go to replace it.

 

I would check with Oliver first.  They may be able to help you.

 

If not you can go to McMaster-Carr.com and do a search for: T-Handle Locking Quick-Release Pins.

 

You will have to measure the size of your pin to get the correct one.

 

Good Luck!


Shirley Arrighi

Share this post


Link to post
Share on other sites

Had the same tight fit on our new Elite II, took my drill and drill index with me when I picked up our new trailer, sure enough the pins were tight and hard to remove, I could push on the rear bumper as someone said and it helped, but taking a 100/1000's off with a larger drill bit did the job and all works as it should now.  I have found that going camping without a drill and drill bits is becoming a necessity more and more.

 

 

 

trainman


Elite II, Twin Bed, Hull #489, 2019 RAM 1500, 5.7 Hemi, 4X4, Crew Cab, 5'7" bed, Towing Package, 3.92 Gears.

Share this post


Link to post
Share on other sites

I have to lean against the bumper to get the pin out on #211.. if I was to drill out a hole I would have to lean on the other side because of the weight. I just lean on both sides as we remove the pins.

Share this post


Link to post
Share on other sites

I just jiggle the bumper while pulling the pins, not a problem. Glad Oliver put a tether on the pins in the later editions, I'm sure I'd be looking for mine if not!!!

 

RB


Cindy,  Russell and  "Harley dog" . Home is our little farm near Winchester TN

2018 Oliver Legacy Elite II - 2018 GMC 2500 Duramax 

"Die young - As late as possible"

ALAZARCACOFLIDMTNVNMOKORTNTXUTWAWYd56201524964bac5483378b34b491562080842sm.jpg

 

 

 

 

Share this post


Link to post
Share on other sites

Talked to Oliver today and ordered a new pin. I will definitely tether it like the other one. Thanks everyone for the input.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  

×
×
  • Create New...