Jump to content

wdw0528

Members
  • Content Count

    67
  • Joined

  • Last visited

Everything posted by wdw0528

  1. Our gas grill (Weber Q1200) all of a sudden would not light recently. I was troubleshooting the grill and almost convinced it was the grill valve. I decided to remove the quick disconnect fitting (where the regulator was removed) and the incoming line was completely clogged/blocked with a tan looking paste like material. After cleaning the blockage I am cooking on the grill again. I share this for the benefit of others who may experience gas flow problems. i am not sure what might have caused this???
  2. Thanks Mossemi - after pasting this I found where you had posted this earlier.
  3. We are living full time in our Oliver while having a home built (in pretty warm temps) and have noticed the A/C dripping some on the inside. I assume/suspect the condensate drain is clogged but am not sure how/where to access it (from the top) after removing the cover. Any tips or advice on this maintenance appreciated.
  4. Update - since we were one week beyond our one year warranty period Oliver was going to have to charge us for the replacement which I believe would have been the older version. I had also reached out to the customer service folks at the WiFi Ranger company and they were great - they agreed to provide the upgraded part under warranty and they held off on shipping until we returned home from our trip. Expecting delivery soon.
  5. No worries mjrendon - I did not take offense :-)
  6. Jason confirmed that it is most likely the step up converter and is going to send us a replacement - will be interesting to see if it is the V2 that John Davies inserted a link for???? BTW - this failure is NOT the result of house batteries falling below 12 volts!!
  7. Thanks Overland - I was already in the process of exploring that area and testing. Looks like the switch (outside the cabinet wall) is okay - it is providing power to a step up converter (photo) I discovered in that access compartment, however there is no power reaching the wifi ranger box itself. Based on what I've learned I'd say that converter is the problem? At this point I have sent an email to Jason Esray and I also plan to reach out to the WiFi Ranger tech support team during their normal business hours this week.
  8. Noticed that we were not picking up a signal from the WiFi ranger that had previously been working fine. Troubleshooting I noticed no lights on the box itself but the switch outside the cabinet (green light for power) seems to be on/working correctly. I have unplugged and replugged the power cord and did not see any power button or on/off switch on the box itself. Any ideas from the community? Anyone else experienced this?
  9. Thanks Janie - don't know how/why I haven't seen this before now but I just looked at your blog and really like the way you have it organized. Thanks for sharing!
  10. It is the same error code (air flow) - and now it is failing randomly for no apparent reason. Sometimes it works and sometimes not - but manipulating the switch gets it started again.
  11. The story continues - we are now in Lake Placid New York and still need heat and you guessed it - it failed again overnight. I only post this to share the "new" discovery that may be related. First - the same procedure before (Bill's sail switch manipulation) solved it again but the problem was identical symptoms. The new information to share with the group is that it seems like both times this happened on this trip was when we ran out of propane and switched to a new tank...maybe a coincidence - don't know. But this time I am also noticing (haven't noticed this before) that the valv
  12. We have the same bike rack and regret not having them "show" us how to remove and replace it during delivery. Once I got it home I decided to do it so it would not be a new procedure at the time we had a flat tire and needed to do it. It was VERY DIFFICULT to get the bike rack off. There were shavings from the drilling left in the square tubing that made it a challenge. This is not a simple one man job in my opinion....at least not ours! I recommend anyone that has this rack to do that drill so you can understand the level of effort it will take to do the job.
  13. Updated status I apologize for the delay but I'd been busy trying to resolve the problem and then we had either no or inconsistent internet (not that it is much better now). After posting this and also sending an email to Jason Essary I got replies from both places and I appreciate them all - thanks. I will provide some details below that will answer some of your questions and hopefully help someone in a similar situation. Our heater is an Atwood and the reset button (until now I didn't know it had one) is located inside the heater the cover (accessed from outside the camper - n
  14. We are in Quebec City and the weather is cool but unfortunately our heater has decided to not work. Symptoms: the heater attempts to come on via the thermostat and we get a fan blowing for about a minute or two and then it shuts down. We had a similar problem before (another camper) and it turned out to be a safety switch that doesn't allow the gas to flow until the chamber is cleared by the fan...seems like similar symptoms. The only difference is with this one I am not hearing the ignitor attempt to light at all Any tips on troubleshooting (that will not void the warranty) or other
  15. Sorry for the delayed response - we are traveling in areas with little or no cell and internet service :-) We are happy with our choices - we have the following: Fiber Granite - Paradise Beach (white) Flooring - Loneseal MW377 Fabric - Mink IN105 These descriptions were taken directly from the bill of sale.
  16. Ditto to what John Davies said - ours (delivered in Feb this year) had the wrong fuse and it blew during the first week/trip out. Other challenges (in addition to changing the fuse) and lessons learned for us are: Storage when not in use - we initially stored the trailer with the fan running and the compost material (not emptied) was drying out too much and moisture is a requirement. We now unplug the fan when it is stored and I will check and add water every other week or so (as required) in an attempt to keep the compost at the proper consistency - working better. Bugs - anoth
  17. That would be cool.....we will be there (Acadia) the first week of September. Will keep an eye out for you!
  18. Thanks Sherry - we know we are late arriving in that area this year and will likely be run out by approaching cold weather.....but this trip will help shape our itinerary for the next visit there. Your post sent me googling “poutine” - I have had the Canadian fries with gravy so we will look for this version while there.
  19. We are leaving late August for Acadia National Park followed by a visit to Quebec City and a loop around the Gaspe peninsula. I am interested in advice/stories/suggestions from anyone else who has made this trip. The only reservations we have made are in Acadia (several days in Blackwoods campground and several days in Schoodic campground). We are limited on when we can leave (third week in August) but are not limited on the return except by the weather as it turns colder. We plan to hang out in the New England states and enjoy the fall colors. BTW - I know we need to see more in that a
  20. I got this one: https://www.amazon.com/gp/product/B01JY9QAPQ/ref=oh_aui_search_detailpage?ie=UTF8&psc=1 and I needed it on the maiden voyage. It stows easily and feels good and sturdy.
  21. The manual that Bill Townes posted a link to is good for the assembly and for the part number - if you decide to order (Like Chris and Duke) no problem, if you still want me to take it off and mail I can do it. Let me know either way.
  22. I do have both of the brace arms with the orange clips.....not sure how to remove the clip though? I can either send you the complete arm or get info from someone on how to remove the clip. Either way I am happy to get it to you.
  23. At the rally earlier this month there were a few owners that had awning damage from the strong storms that blew through. One directly across from us lost their entire awning and asked if I could haul it to the dumpster area for them since I had a truck. I did so, but before I did I cannibalized any undamaged parts that I could carry with the intent of offering them here for any owner that might need any of them. The awning was a Carefree awning. I salvaged the fabric, support arms, and several other pieces of hardware. If any of you are in need of any parts that I may have, jus
  24. After a recent job of cleaning and waxing followed by a rain I am noticing some "fairly minor" black streaking from the rubber gaskets behind the exterior lights. It seems to wipe off pretty easily so far (since I am catching it early) - wonder if anyone else is having an issue with streaking and if so, what are you doing to prevent it or correct it? I was told when I asked about streaking problems during our delivery that we might want to apply a bead of clear RTV sealant around those seals/gaskets in order to better seal and prevent any streaking. Has anyone done this and do you have an
  25. Ours is fairly new (Feb delivery) so not a lot of experience but we did ask a lot of questions at the plant and here on the forum. We have been washing with a turtle wash/wax solutions when dirty and after the last wash I put the first coat of wax on it. Based on recommendations I plan to do at least yearly but possibly two times a year. We went to a West Marine and asked for recommendations and this is the product that they told us was best/most popular: https://www.amazon.com/gp/product/B01MSZRRWU/ref=ox_sc_sfl_title_2?ie=UTF8&psc=1&smid=ATVPDKIKX0DER It goes on as a l
×
×
  • Create New...