Jump to content

Search the Community

Showing results for tags 'solar'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


  • News & Announcements
    • Oliver Technical Service Bulletins
    • Oliver Safety Recall Bulletins
    • General Announcements
  • Oliver Forums
    • Welcome To The Oliver Travel Trailer Forums
    • How to Join and Use Oliver Travel Trailer Forums
    • Introduce Yourself
  • Oliver Campers
    • Delivery Day Photos
    • Mechanical & Technical Tips
    • Ollie Modifications
    • Towing an Oliver
    • Service Talk
  • Oliver Camping
    • Campgrounds & Parks
    • Events & Rallies
    • Ollie Boondocking
    • Submit Your Story
  • Oliver Campfire
    • General Discussion
    • Oliver Blogs

Find results in...

Find results that contain...

Date Created

  • Start


Last Updated

  • Start


Filter by number of...


  • Start



About Me

Gender or Couple


Found 7 results

  1. Thanks to the new narrow panel size that Zamp designed to fit Airstreams, I think you could make it work. No TV antenna, of course, like the 480W system. The trick would be to straddle the AC and MaxxFan with the narrow panels. There's just enough width between them and should be just enough length to maintain the Penguin II clearance requirements at the back of the unit. Here's how it might work. The three panels at the front are what Oliver will do for a 480W system - all I did was add the two narrow 80W panels to the rear. Worst case, they'd just need to use a low profile plumbing vent to slide the panels forward enough, or slide the AC back a bit, just to maintain the AC clearances. Add a couple Zamp 200W portable panels, and you've got yourself a 1kW mobile power station.
  2. I am camped about 20 miles south on Seligman Arizona with Hull 519, delivered in September. From the beginning it seemed like I lost voltage too fast or the solar didn’t charge much. But it is much worse now. I ran the generator last night and got it to 12.1, dropped to 11.5 off of the generator. This morning I was at 9.1 volts running almost nothing but the heater (40 degrees at night). So I fired up the generator again at 4AM so we could go hunting. Got it to 12.5 and left it with nothing running in full Arizona sun all day. Came back to 10 volts at 2PM. My sister had 13.5 in her Forest River. I find nothing loose or obviously wrong in the battery tray, under the couch or at the panel under the dinette. The panel indicates charging on solar but voltage never gets very high and drops like a rock with no input. Seems to be getting worse, like something is drawing a lot of juice. I am running almost nothing. Is there anything at all that I can check or fix or work around? I can’t stay on the hunt like this.
  3. This size seems like it would fit on both sides up top. The feet are even made for curved roofs. There is even an extra plug-in on the factory roof install for the solar panels. It would be super easy if you could get an SEA splitter cable and just plug them in, then you would just have to mount the feet. Just wondering if anyone has done anything like this. The whole parallel vs series and panel compatibility is beyond my expertise. Though it would be nice to have a 500W system. https://www.zampsolar.com/90watt-long-expansion https://www.zampsolar.com/y-connector 30-AD-90L-InstallGuide.pdf
  4. We have, on our 2018 LEII: 4-6v AGM batteries 2 Solar Panels (320w) ZS-30A Charge Controller 2000w Inverter Composting Toilet with 12v dc fan We know the solar panels charge the batteries through the controller. Does anything else help to charge them? On the charging side: When plugged into 30a 110v, does the AC system charge the batteries? When plugged into 15a 110v, does the AC system charge the batteries? (Like when running the generator when boondocking or using friends AC when driveway surfiing.) When plugged into the TV with 7 pin connector, does the TV DC supply help charge the batteries? In times of bad solar charging weather, how do I charge the batteries? Or is just the solar doing all of the battery charging? On the consumption side, what draws power from the batteries when plugged into: 30a 110v? 15a 110v? TV 7 pin with engine running? Today the tank monitor shows the batteries at 13.5v after a full day of bright sunlight. What are we supposed to avoid dropping the level below, in volts, to avoid damaging the batteries? Some part of me thinks the batteries should be charged and most demand be met by whatever external power supply you happen to be using (including solar). Wishful thinking? Cheers, Mark
  5. Seems my Zamp charge controller is offline - at night, but where do you pick up charge information when on shore power, and no solar charge? Or am I over thinking this. I'll give Oliver a call, the manual is very lite in this respect.
  6. Yes, I did a factory tour, yes, I thought and thought and thought, yes, I've crunched numbers til I can't crunch any longer and YES, I paid my deposit last week and locked in a production date! Now....Decision time. Solar or no? AGM batteries or no? I am a life long camper, retired school counselor and do not have unlimited financial resources. BUT, I do want to do this Ollie right. Thoughts, opinions, guidance sought?!??
  7. Knowledge Base Article for Zamp Solar ZS-30A Charge Controller The Zamp Solar 30 Amp 5 Stage Digital Deluxe Solar Charge Controller # ZS-30A has PWM or Pulse Width Modulation, which is a digital signal that is used to control power applications and has 5 stages of charging for best battery health and longevity. This controller can support and is programmable for the 4 typical types of deep cycle batteries – WET, GEL, AGM and Calcium. We pre-set the controller at the factory according to what batteries are installed. 12 volt solar charging power. LCD screen displays battery voltage, charging current, charging capacity, battery types and faulty codes. LED light indicators show charging status and battery condition. 5 stages of charging: Level 1 – Soft Charge – When batteries suffer an over-discharge, the controller will softly ramp the battery voltage up to 10V. Level 2 – Bulk Charge – Maximum current until batteries rise to Absorption Level. Level 3 – Absorption Charge – Constant voltage charging (battery is over 85%). This stage takes longer than any other stage to complete. You will typically see your battery status remain in this stage unless you are not using the camper. The full battery indicator is about the last 2% and while running lights and other components it will remain in the absorption stage. *Battery volts displayed during this stage are charging volts not actual battery volts. Level 4 – Equalization Charge – Only for WET battery or Calcium battery type. When the battery is deeply drained below 10V, it will automatically run this stage to bring the internal cells to equal states and fully complement the loss of capacity. (Gel and AGM batteries do not run Equalization Charge). Level 5 – Float Charge – Battery is fully charged and maintained at a safe level. Fully charge is more than 13.6V. Includes a port for an optional external battery temperature sensor. Zamp Charge Controller & Digital Monitoring System (Battery Volts) Both systems will display charging volts rather than actual battery volts when power is being supplied to the batteries. Customer interaction The charge controller has 2 buttons. One button labeled Amp/Volts can be used to scroll through relevant information Amp/Volt Button Current battery volts or charging volts Current Amps being supplied to the battery (Initial startup will be lower amps and slowly increase to maximum output depending on sunlight available. Current total of Amp Hours supplied within the 24 hour timeframe. This setting will reset with every 24 hour period. Current Battery Temperature. (Displayed in Celsius). This is used by the charge controller to monitor the battery. Battery Type Button This is pre-set at the factory based on the type of batteries installed and should only be changed if you replace your batteries with a different battery type. Zamp Error Codes: P01 - Solar Panel Reverse Connection P02 - Solar Panel Over Voltage 601 - Battery Disconnected or less than 3.0 Volts 602 - Battery Reverse Connection 603 - Battery Over Voltage (> 17.5 Volts) 604 - Battery Temperature over 65C
  • Create New...