Snackchaser Posted February 10, 2025 Posted February 10, 2025 This is yet another modification for instant hot water. I was inspired by @Minnesota Oli who brilliantly installed a timed solenoid valve to circulate hot water from the bathroom faucet back to the freshwater tank. This saves from wasting water down the drain while waiting for it to get hot. I loved the concept of using a timer, but I went with a recirculating pump instead of a solenoid valve. We’ve used this design for about a year now, and it’s been very luxurious and effective. Not only does it help conserve fresh water, it prolongs the grey water tank volume which is now our most limiting factor when boondocking. The recirculation pump is started from momentary push button switches installed at each faucet. The button(s) activate a timer/relay that runs the pump for 25 seconds. Experimentation showed that 25 seconds sufficiently heats the pipes to deliver hot water at full temperature. The pump circulates the hot water back to the hot water heater, rather than into the fresh water tank. The new recirculation pump is the same model as the existing main pump. It was connected with flexible faucet hoses to reduce vibration and isolation valves so it can be used as a spare if needed. The pump was mounted on a plywood board fastened with construction glue to the vertical fiberglass surface by the furnace return vent. Note: Pump pressures can vary, so it might be necessary to slightly adjust the pump pressure switch to overcome the house pump pressure. Also, the pump may not overcome some of the higher city water pressures if a pressure regulator isn’t used. . . as it should be regardless. The Oliver has two separate hot water loops that I joined together so that the kitchen faucet is included in the recirculation loop. Being a shorter loop, there was less water wasted while waiting for it to get hot, but it's used more frequently so it's worth it to join the loops. There is plenty of room under the floor and behind the cabinets to run PEX return lines. “T” fittings were installed at the kitchen and bathroom faucets, and at the water heater input as shown on the drawing. Note: There was a buried 3-way valve, flexible by-pass hose, and a (clogged open) check-valve for water heater isolation. It was restricting flow and pinching the furnace duct so I completely removed it. The Water Heater can be easily isolated other ways if the need arises. The momentary push buttons were arbitrarily programed so that they must be depressed for one second before the pump will start. The buttons were non-intrusively mounted in 1/2” holes. The bathroom button is behind the existing bathroom pump switch, the kitchen button is above the sink, and the outdoor shower button is inside the shower wand enclosure. The sheathed button wiring is joined together under the street side bed along with the timer. I used terminal blocks, but wiring could be joined with any number of splicing methods. The button wiring carries no measurable voltage or current, it’s simply a switch to “low” (ground) for the timer trigger. Wire runs to the bathroom and outdoor shower switches are pretty straight forward, the bathroom vanity shelf needs to be removed for access. The kitchen switch wiring is laid under the liners in the upper cabinet, through the attic, and down the rear wall next to the clear AC drain tubing. I used a programmable timer/relay for the pump. An inexpensive (re-usable) Programer is also needed to program the timer. The Programer has built in App and Bluetooth for programing it on a smart phone and I’ve provided a screen shot of the program settings. This is truly simple to do, and quite fun! As many in this forum know, the Tuma Comfort II water heaters have a built-in circulation pump, controlled by temperature sensors, that keeps a small internal tank ready with hot water. Only one part (unavailable to public) differentiates it from the Truma Comfort II “Plus” that has a full hot water recirculating system. It took a few years, but I finally have the design details for that part and I’ll try to fabricate one when the Truma is removed for the up-coming factory recall work. More to come if I’m successful. The Truma “Plus” recirculation system provides true instant hot water (when not in Eco mode) because it keeps hot water circulating through the system based on temperature sensors. My system has a 25 second delay before the water is hot, then it cools down until the button is pushed again. This is less convenient, but more energy efficient because it doesn’t periodically cycle. I’m still on the fence which system is better, but fortunately the recirculation loop installed in this modification will work for both systems. Hope someone finds this useful! Cheers! Geoff Shopping list: Sureflow pump https://a.co/d/cSLUWEF 10 amp Timer/Relay https://a.co/d/g6C1zaZ Timer/Relay Programer https://a.co/d/9h1HtK6 Momentary switches https://a.co/d/i9wwhNs Terminal Blocks https://a.co/d/bkgrKhh Red PEX and fittings Flexible faucet hoses 1/4 turn valves 3 5 4 1
Galileo Posted September 7, 2025 Posted September 7, 2025 Thanks for this! I’d really limited my use of the hot water on our Oliver because the system is so poorly designed. I suppose it’s fine if you’re hooked up to city water - and a sewer connection - but for other situations it’s pretty terrible. I don’t know if I’d go through the trouble of the timers or temperature sensors, but knowing that somebody has done this is reassuring. It’s bad enough when someone designs or builds a home with the water heater long distances from the points of use, but in an RV with limited tankage, it’s really ridiculous. 1 1 2022 Oliver Legacy Elite II Hull #1029 King Bed Floorplan electronics package Truma Aqua-Go LOUD Dometic Penguin A/C LevelMate Pro+ Valterra Electric Black Tank Dump Valve TV - 2025 GMC Sierra 1500 Denali, 3.0l Duramax Diesel, Crew Cab 4WD (17.9mpg towing, 35mpg clean) RealTruck hard tonneau cover Rove R2-4K DashCams Canada: New Brunswick, Nova Scotia, Prince Edward Island
Jls Posted yesterday at 06:38 PM Posted yesterday at 06:38 PM This such a great idea. Wish I was handy enough to do. So in lieu, I just run water into a jar until I get warm water and use the jar water in the kitchen to heat for coffee or tea. 2
Moderators topgun2 Posted 23 hours ago Moderators Posted 23 hours ago Well - Since Galileo has the "fancy" Truma versus the decidedly "unfancy" Suburban water heater My solution for this issue is of no use to him. And, if Jls also has a "fancy" water heater, he too can not use my solution. However, for those of us that still chose to live back in the "Stone Age", I've listed a mod here on the Forum where I simply use a "cabled" meat thermometer with the sensor end placed under the water heater tank's insulation and the readout placed just outside the furnace cold air return. Turn on the water heater and observe the reading on the thermometer. When it reads something in the mid-90's then the water in my tank is about 104 degrees. At this point I shut the water heater off, get in the shower and ONLY use the hot water to shower (i.e. no cold water mixing necessary nor is there any short burst of cold water when turning the water back on during military showers). There is still the short delay when first turning on the water where the water is cool/cold while it gets from the hot water tank to the showerhead, but, if that small amount of water is critical I can catch it in a small bowl/glass/jar for use later as Jls is presently doing. Bill 1 2 1 2023 Ford F150 Lariat 3.5EB FX4 Max Towing, Max Payload, 2016 Oliver Elite II - Hull #117 "Twist" Near Asheville, NC
Geronimo John Posted 21 hours ago Posted 21 hours ago (edited) Great design Geoff! In our case, we rarely use the outside shower and the kitchen sink is close to the hot water heater. So a KISS approach is just circulate water to the bathroom sink. Materials: SPDT 12V A/B switch 12V 2-way diverter solenoid operated valve (often called a 3-port or Y-diverter valve) 12V line from source to switch to valve to existing OEM pump PEC line from sink cabinet to water heater inlet pipe PEC Check Valve Miscellaneous hardware How: Run circuit from 12V source to switch, valve and OTT OEM Pump. Run Pec from bathroom sink hot water line "T" to hot water heater inlet line "T". Normally Open would have the valve off and the 12V line to the existing pump would be off as well. Flip it to the other way, and the valve would divert water back to the tank, and energize the OEM pump for circulation. I believe this would overide the normal run sensor. One could use a push to contact switch if preferred. Or just remember to return the switch to Normally Open position when hot water arrives. Would this idea work? GJ Edited 21 hours ago by Geronimo John 1 1 TV: 2019 F-150 SuperCrew Lariat, 3.5L EcoBoost, 10 Speed Trans, Max Tow, FX-4, Rear Locker OLLIE: 2018 OE2 Hull 342, Twin Bed. OLLIE DIY’s: Timken Bearings, BB LiFePO4's, Victron 712 Smart, 350 Amp Master Switch, Houghton 3400, Victron Orion DC - DC, 3000-Watt Renogy Inverter, P.D. 60-amp Converter, Frig Dual Exhaust Fans, Kitchen Drawer Straps. Front Wardrobe Shelves, Snuggle Shelf. TV DIY’s: 2 5/16" Anderson System, Nitto recon’s, Firestone Rear Air Bags, Bilstein 5100’s, Mud Flaps & Weather Tech all, installed Ham Radio (WH6JPR).
Snackchaser Posted 12 hours ago Author Posted 12 hours ago 9 hours ago, Geronimo John said: Would this idea work? Yes that should work great! Same concept as what @Minnesota Oli installed, less the timer!
Dean and Mary Posted 2 hours ago Posted 2 hours ago On 2/9/2025 at 11:31 PM, Snackchaser said: Not only does it help conserve fresh water, it prolongs the grey water tank volume which is now our most limiting factor when boondocking. The dual-purpose nature of this project makes it even more intriguing. It's definitely something I'll be thinking about once I finish my 12-volt upgrade. Thanks for sharing, Dean TV: 2019 F-150 Super Crew Lariat, 3.5L EcoBoost, 10 Speed Transmission, Max Tow and Offroad package. Oliver: 2022 – Hull 953, Twin Bed, with Lithium Platinum Package (640ah Lithionics lithium batteries), Outdoor Pro Package, 16” wheels, D52 axles, 5-leaf Alcan Spring package, Bulldog HD Shock Absorbers, 2 5/16 Bulldog coupler and LT tires. After market: Victron MultiPlus-II 12/4000, Two Victron 100/50 MPPT Solar Charge Controllers, Victron IP65 500A/50mV SmartShunt, Victron Lynx Distributor, Orion DC-DC charger 12/12V 50A 700W, Cerbo GX MK2 with GX Touch 70 Display. Misc: Custom Wood Accessories by Foybles. Seabiscuit Metal Designs front storage box and moose rack.
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now