GarryandKristi Posted June 16, 2020 Share Posted June 16, 2020 We went dry camping this past weekend and when my wife started the Kuerig using an outlet on the bed stand. The machine started then stopped. I thought it was an inverter issue as the microwave went dead too. Went we got home I started debugging and found that not all outlets were dead and all behaved the same whether on shore power or inverter. Turns out a splice in the outlet on the twin bed street side had come loose. All the outlets are on one circuit but both receptacles on each bed side (twin bed arrangement) have splices in the receptacles and a bad splice means that all “downstream” outlets will not work. The outlets are SCD (self-contained device style and instead of terminal screws or push connects have slotted copper bands where the neutral, hot, and ground wires go. They can be wired as pass-through or spliced or end of line. It requires an installation tool to properly press the wire into the SCD slots. The top slice virtually fell out as I opened the receptacle cover. If the Oliver folks used a tool, they didn’t do a very good job. I also opened the receptacle that the Kuerig was plugged into and that pass-through insertion was not solid either. The receptacle specs and installation guide is here: https://mobilehomepartsstore.com/Merchant2/documents/scd-instructions.pdf I decided to get this installation tool as I figure there is a strong possibility that this issue may surface again https://www.magicmobilehomesupply.com/SCDT-Tool-p/3795.htm I also noted that the wiring diagram had errors. There is not a separate leg to the microwave outlet - all outlets are served by 1- 12/2 Rolex cable. The breaker for the outlets was also mislabeled (we have Truma/inverter/no solar. We also have a receptacle inside the closet as well as outside and only one was on the wiring diagram. I think the outlet inside the closet was added a couple years ago. The photo shows the inside of the SCD with the failed spice connection. The slice connection is listed as one of the connection methods but a pass-through would probably be better as it would not affect the other “downstream” receptacles. Hopefully this will help someone if something similar happens. I spent hours tracing wires checking voltage and continuity, etc. before I found the issue. 5 1 Garry and Kristi Apex, NC 2018 Oliver Elite II Hull 372 TV 2015 Ram 1500 3.0 L EcoDiesel Link to comment Share on other sites More sharing options...
Overland Posted June 17, 2020 Share Posted June 17, 2020 Interesting problem, thanks for making everyone aware. I wasn’t familiar with that type of outlet, and tbh, it doesn’t seem like the type of connection that would hold up well in an environment with lots of vibration, even though these seem to have been designed for RVs? I might have to do some reading. Link to comment Share on other sites More sharing options...
Moderator+ ScubaRx Posted June 17, 2020 Moderator+ Share Posted June 17, 2020 I would replace the outlets with standard screw type just like you would have in your home. I can see (from your picture) how (in theory) these outlets would make installation easier on a production line. I can also see how these can fail. These are similar to the T Tap Insulation Displacement Connectors used in 12 volt circuits. They are hard to install and get a positive, long lasting connection. I won't use them for low voltage wiring and I don't think I'd want these outlets in my high voltage circuits. Thanks for pointing this out. 2 Steve, Tali and our dog Rocky plus our beloved Storm, Lucy, Maggie and Reacher (all waiting at the Rainbow Bridge) 2008 Legacy Elite I - Outlaw Oliver, Hull #026 | 2014 Legacy Elite II - Outlaw Oliver, Hull #050 | 2022 Silverado High Country 3500HD SRW Diesel 4x4 Link to comment Share on other sites More sharing options...
GarryandKristi Posted June 17, 2020 Author Share Posted June 17, 2020 10 hours ago, ScubaRx said: I would replace the outlets with standard screw type just like you would have in your home. I can see (from your picture) how (in theory) these outlets would make installation easier on a production line. I can also see how these can fail. These are similar to the T Tap Insulation Displacement Connectors used in 12 volt circuits. They are hard to install and get a positive, long lasting connection. I won't use them for low voltage wiring and I don't think I'd want these outlets in my high voltage circuits. Thanks for pointing this out. Replacing them would give peace of mind. The GFCI outlet under the dinette is a standard outlet and connection with a separate outlet box. I am wondering if the non-gfci receptacles that are the scd type are code for trailers and mobile homes? I just hate pulling “big amps” with the microwave at the end of the line with 2 splices prior and a potentially dicey connection at its receptacle. I guess the good thing is that one normally doesn’t run a microwave that long. Garry and Kristi Apex, NC 2018 Oliver Elite II Hull 372 TV 2015 Ram 1500 3.0 L EcoDiesel Link to comment Share on other sites More sharing options...
GraniteStaters Posted June 21, 2020 Share Posted June 21, 2020 I live next to a Snap-on distributor, so I may ask him about getting this tool the next time I see him. Thanks for the post. David Caswell and Paula Saltmarsh Hull 509 "The Swallow" Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now