jd1923 Posted Saturday at 07:07 PM Posted Saturday at 07:07 PM 11 hours ago, Geronimo John said: The real question is their 20 amps a #12 AWG? If so, kiss that 20 amps good bye The black AUX wire on the 7-blade connector is 12 AWG. According to this table, 20A on 12 AWG is good for only 10 ft without excessive voltage drop! Anybody have a good table with lengths up to 100 ft? I cropped this table at 70A since the new Orion is 70A. You can see I'm undersized with 4 AWG on the Orion 50A, and Dean installing 1/0 is just right. Running 20A on 12 AWG for 80-100 ft is dangerous. OTT should not be advertising this capability, nor installing it. I would disconnect the Black AUX wire on the new Olivers, just like we did on our older hulls. Then discard the generic 20A charger and install a Victron Orion XS with dedicated wiring. Chris & John in Prescott, AZ | 2016 EII #113 | '01 Ram 2500 Cummins!
Snackchaser Posted Saturday at 07:51 PM Posted Saturday at 07:51 PM 37 minutes ago, jd1923 said: Running 20A on 12 AWG for 80-100 ft is dangerous. Whoa! Let's take a step back here. The 3.2 V figure is right for 100 ft of 12 AWG, but the better 7-pin cords use 10 AWG for the 12 volt wire, which is good for 30 amps. Also consider that most trucks use chassis ground for the negative, and the trailer side is likely heavier wire past the 7-pin junction box. So realistically there is a lot less voltage drop than you think, it’s more likely under 1.5 V at 20 amps. And remember it’s rated 10 to 20 amps depending on the TV. That voltage drop would not work with direct charging, but it’s exactly what a DC-to-DC charger is for. It regulates output so the battery gets full charging voltage. The drop only affects how much input voltage the charger has to work with and loss through heat. That's why it depends on what the truck can deliver… which is the reason of a 10 to 20 amp range. So it’s not unsafe, and Oliver wouldn’t do if it was! 10 AWG is rated comfortably above the 25 A maximum draw with voltage drop. The truck’s 30 amp fuse backs that up. The only thing worth watching is the 7-pin plug contacts. Keep them clean, and check for heat after a long drive. Cheers! Geoff 1
jd1923 Posted Saturday at 08:15 PM Posted Saturday at 08:15 PM (edited) 2 hours ago, Snackchaser said: but the better 7-pin cords use 10 AWG for the 12 volt wire, which is good for 30 amps. Also consider that most trucks use chassis ground for the negative, and the trailer side is likely heavier wire past the 7-pin junction box. Standard 7-wire trailer cords have one (1) 10 AWG the BLUE wire for brakes, two (2) 12 AWG wires (AUX and GROUND) and four (4) 14 AWG wires for lights, signals, etc. This is what's been installed in the 6 trailers I've owned including including Hull #113. Then OTT continued the Black AUX wire with a butt connector under the front dinette (new hulls have the junction box under the vanity) where they crimped on another 10+ ft of #12 wire to the +bus under the streetside bed (more length). I shortened this run when moving the +bus to under the dinette. I also installed a new 7-blade connector on the Oliver. Touching all ends of this, I'm certain of these wire gauges. So 4 AWG is too small for 50A but somehow 12 AWG works for 20A? This makes no sense to me. As I wrote above, my Black AUX wire is disconnected and I wouldn't think to install a 20A charger on it, IMHO not good! Edited Saturday at 10:25 PM by jd1923 Chris & John in Prescott, AZ | 2016 EII #113 | '01 Ram 2500 Cummins!
Geronimo John Posted Sunday at 12:35 AM Posted Sunday at 12:35 AM 4 hours ago, Snackchaser said: The only thing worth watching is the 7-pin plug contacts. Keep them clean, and check for heat after a long drive Watching for 7-Pinheat build up is a good idea for all of us DC/DC owners. Our OEM OTT 7-pin died as a result of the paltry 20+ amps our DC/DC was putting out. Hence suggest adding a spare 7-wire plug and maybe the TV receptical to the spare parts drawer. GJ TV: 2019 F-150 SuperCrew Lariat, 3.5L EcoBoost, 10 Speed Trans, Max Tow, FX-4, Rear Locker OLLIE: 2018 OE2 Hull 342, Twin Bed. OLLIE DIY’s: Timken Bearings, BB LiFePO4's, Victron 712 Smart, 350 Amp Master Switch, Houghton 3400, Victron Orion DC - DC, 3000-Watt Renogy Inverter, P.D. 60-amp Converter, Frig Dual Exhaust Fans, Kitchen Drawer Straps. Front Wardrobe Shelves, Snuggle Shelf. TV DIY’s: 2 5/16" Anderson System, Nitto recon’s, Firestone Rear Air Bags, Bilstein 5100’s, Mud Flaps & Weather Tech all, installed Ham Radio (WH6JPR).
BackofBeyond Posted Sunday at 01:43 PM Posted Sunday at 01:43 PM Amps are amps and wire gauge and v loss all matter - in any case - the GM aux is fused at 30 amps. Wire sized for 80% continuous (12awg)?? The draw/load is determined by dc/dc system in the Oliver - I don't know anything about that system, and so far, Oliver has not elaborated on it either. I can only believe the system regulates that draw and is designed within the std 7 pin OEM specs. Overheating due to excessive draw would be a design flaw in my mind. Real world - things get loose, dirty, worn, and the current draw can create heat - and yes, it makes sense to monitor that connection. If you were really worried about excessive amperage, install an inline fuse on the AUX circuit to match the amperage ratings of the installed wire/cord. If you keep blowing fuse - something is wrong. It makes sense that the OEM DC/DC in the Oliver is not there to charge at high rates, I would relate it more to a trickle charge - enough to run refrigeration and dump a few watts into the battery - at best. Want big charging - go big wire, quality controllers, high end connectors, and understand how the TV electrical management systems see this load and make connections accordingly. Thus, this threads original topic. Gee, you can learn so much on this forum. 1 Cindy, Russell and "Harley dog" . Winchester TN 2027 EII on the production board. "Ramble On" 2026 Chevrolet 2500 ZR2, 6.6L L8T gas V8 "Die young - As late as possible"
Dean and Mary Posted Sunday at 03:45 PM Posted Sunday at 03:45 PM 1 hour ago, BackofBeyond said: It makes sense that the OEM DC/DC in the Oliver is not there to charge at high rates, I would relate it more to a trickle charge - enough to run refrigeration and dump a few watts into the battery - at best. Thanks for the clarification on the Oliver having a factory-installed DC-to-DC charger. Thinking about it more, it makes perfect sense that Oliver would include one. This approach will work well for many Oliver owners because it provides some additional charging while driving without requiring any modifications to the tow vehicle. While it may not offer the charging performance of a larger after market system and related heavy gauge wiring, it is a simple, turnkey solution that should meet the needs of a large percentage of owners. TV: 2019 F-150 Super Crew Lariat, 3.5L EcoBoost, 10 Speed Transmission, Max Tow and Offroad package. Oliver: 2022 – Hull 953, Twin Bed, with Lithium Platinum Package (640ah Lithionics lithium batteries), Outdoor Pro Package, 16” wheels, D52 axles, 5-leaf Alcan Spring package, Bulldog HD Shock Absorbers, 2 5/16 Bulldog coupler and LT tires. After market: Victron MultiPlus-II 12/4000, Two Victron 100/50 MPPT Solar Charge Controllers, Victron IP65 500A/50mV SmartShunt, Victron Lynx Distributor, Orion DC-DC charger 12/12V 50A 700W, Cerbo GX MK2 with GX Touch 70 Display. Misc: Custom Wood Accessories by Foybles. Seabiscuit Metal Designs front storage box and moose rack.
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now