jd1923 Posted November 14 Posted November 14 11 hours ago, Geronimo John said: The real question is their 20 amps a #12 AWG? If so, kiss that 20 amps good bye The black AUX wire on the 7-blade connector is 12 AWG. According to this table, 20A on 12 AWG is good for only 10 ft without excessive voltage drop! Anybody have a good table with lengths up to 100 ft? I cropped this table at 70A since the new Orion is 70A. You can see I'm undersized with 4 AWG on the Orion 50A, and Dean installing 1/0 is just right. Running 20A on 12 AWG for 80-100 ft is dangerous. OTT should not be advertising this capability, nor installing it. I would disconnect the Black AUX wire on the new Olivers, just like we did on our older hulls. Then discard the generic 20A charger and install a Victron Orion XS with dedicated wiring. Chris & John in Prescott, AZ | 2016 EII #113 | '01 Ram 2500 Cummins!
Snackchaser Posted November 14 Posted November 14 37 minutes ago, jd1923 said: Running 20A on 12 AWG for 80-100 ft is dangerous. Whoa! Let's take a step back here. The 3.2 V figure is right for 100 ft of 12 AWG, but the better 7-pin cords use 10 AWG for the 12 volt wire, which is good for 30 amps. Also consider that most trucks use chassis ground for the negative, and the trailer side is likely heavier wire past the 7-pin junction box. So realistically there is a lot less voltage drop than you think, it’s more likely under 1.5 V at 20 amps. And remember it’s rated 10 to 20 amps depending on the TV. That voltage drop would not work with direct charging, but it’s exactly what a DC-to-DC charger is for. It regulates output so the battery gets full charging voltage. The drop only affects how much input voltage the charger has to work with and loss through heat. That's why it depends on what the truck can deliver… which is the reason of a 10 to 20 amp range. So it’s not unsafe, and Oliver wouldn’t do if it was! 10 AWG is rated comfortably above the 25 A maximum draw with voltage drop. The truck’s 30 amp fuse backs that up. The only thing worth watching is the 7-pin plug contacts. Keep them clean, and check for heat after a long drive. Cheers! Geoff 1
jd1923 Posted November 14 Posted November 14 (edited) 2 hours ago, Snackchaser said: but the better 7-pin cords use 10 AWG for the 12 volt wire, which is good for 30 amps. Also consider that most trucks use chassis ground for the negative, and the trailer side is likely heavier wire past the 7-pin junction box. Standard 7-wire trailer cords have one (1) 10 AWG the BLUE wire for brakes, two (2) 12 AWG wires (AUX and GROUND) and four (4) 14 AWG wires for lights, signals, etc. This is what's been installed in the 6 trailers I've owned including including Hull #113. Then OTT continued the Black AUX wire with a butt connector under the front dinette (new hulls have the junction box under the vanity) where they crimped on another 10+ ft of #12 wire to the +bus under the streetside bed (more length). I shortened this run when moving the +bus to under the dinette. I also installed a new 7-blade connector on the Oliver. Touching all ends of this, I'm certain of these wire gauges. So 4 AWG is too small for 50A but somehow 12 AWG works for 20A? This makes no sense to me. As I wrote above, my Black AUX wire is disconnected and I wouldn't think to install a 20A charger on it, IMHO not good! Edited November 14 by jd1923 Chris & John in Prescott, AZ | 2016 EII #113 | '01 Ram 2500 Cummins!
Geronimo John Posted November 15 Posted November 15 4 hours ago, Snackchaser said: The only thing worth watching is the 7-pin plug contacts. Keep them clean, and check for heat after a long drive Watching for 7-Pinheat build up is a good idea for all of us DC/DC owners. Our OEM OTT 7-pin died as a result of the paltry 20+ amps our DC/DC was putting out. Hence suggest adding a spare 7-wire plug and maybe the TV receptical to the spare parts drawer. GJ TV: 2019 F-150 SuperCrew Lariat, 3.5L EcoBoost, 10 Speed Trans, Max Tow, FX-4, Rear Locker OLLIE: 2018 OE2 Hull 342, Twin Bed. OLLIE DIY’s: Timken Bearings, BB LiFePO4's, Victron 712 Smart, 350 Amp Master Switch, Houghton 3400, Victron Orion DC - DC, 3000-Watt Renogy Inverter, P.D. 60-amp Converter, Frig Dual Exhaust Fans, Kitchen Drawer Straps. Front Wardrobe Shelves, Snuggle Shelf. TV DIY’s: 2 5/16" Anderson System, Nitto recon’s, Firestone Rear Air Bags, Bilstein 5100’s, Mud Flaps & Weather Tech all, installed Ham Radio (WH6JPR).
BackofBeyond Posted November 15 Posted November 15 Amps are amps and wire gauge and v loss all matter - in any case - the GM aux is fused at 30 amps. Wire sized for 80% continuous (12awg)?? The draw/load is determined by dc/dc system in the Oliver - I don't know anything about that system, and so far, Oliver has not elaborated on it either. I can only believe the system regulates that draw and is designed within the std 7 pin OEM specs. Overheating due to excessive draw would be a design flaw in my mind. Real world - things get loose, dirty, worn, and the current draw can create heat - and yes, it makes sense to monitor that connection. If you were really worried about excessive amperage, install an inline fuse on the AUX circuit to match the amperage ratings of the installed wire/cord. If you keep blowing fuse - something is wrong. It makes sense that the OEM DC/DC in the Oliver is not there to charge at high rates, I would relate it more to a trickle charge - enough to run refrigeration and dump a few watts into the battery - at best. Want big charging - go big wire, quality controllers, high end connectors, and understand how the TV electrical management systems see this load and make connections accordingly. Thus, this threads original topic. Gee, you can learn so much on this forum. 2 Cindy, Russell and "Harley dog" . Winchester TN 2027 EII on the production board. "Ramble On" 2026 Chevrolet 2500 ZR2, 6.6L L8T gas V8 "Die young - As late as possible"
Dean and Mary Posted November 15 Posted November 15 1 hour ago, BackofBeyond said: It makes sense that the OEM DC/DC in the Oliver is not there to charge at high rates, I would relate it more to a trickle charge - enough to run refrigeration and dump a few watts into the battery - at best. Thanks for the clarification on the Oliver having a factory-installed DC-to-DC charger. Thinking about it more, it makes perfect sense that Oliver would include one. This approach will work well for many Oliver owners because it provides some additional charging while driving without requiring any modifications to the tow vehicle. While it may not offer the charging performance of a larger after market system and related heavy gauge wiring, it is a simple, turnkey solution that should meet the needs of a large percentage of owners. TV: 2019 F-150 Super Crew Lariat, 3.5L EcoBoost, 10 Speed Transmission, Max Tow and Offroad package. Oliver: 2022 – Hull 953, Twin Bed, with Lithium Platinum Package (640ah Lithionics lithium batteries), Outdoor Pro Package, 16” wheels, D52 axles, 5-leaf Alcan Spring package, Bulldog HD Shock Absorbers, 2 5/16 Bulldog coupler and LT tires. After market: Victron MultiPlus-II 12/4000, Two Victron 100/50 MPPT Solar Charge Controllers, Victron IP65 500A/50mV SmartShunt, Victron Lynx Distributor, Orion DC-DC charger 12/12V 50A 700W, Cerbo GX MK2 with GX Touch 70 Display. Misc: Custom Wood Accessories by Foybles. Seabiscuit Metal Designs front storage box and moose rack.
Geronimo John Posted 22 hours ago Posted 22 hours ago (edited) On 11/15/2026 at 5:45 AM, Dean and Mary said: While it may not offer the charging performance of a larger after market system and related heavy gauge wiring, it is a simple, turnkey solution that should meet the needs of a large percentage of owners. I believe that the charge wire is sized to provide code required charging of the Emeregency Break-Away System battery. For our OTT's, the battery power for that emergency system is the main batteries. The seven-pin connector wire size is minimal for charging OTT house batteries at our typical 100+ out and back wire lenghts. Edited 4 hours ago by Geronimo John Updated per JD's thoughts... TV: 2019 F-150 SuperCrew Lariat, 3.5L EcoBoost, 10 Speed Trans, Max Tow, FX-4, Rear Locker OLLIE: 2018 OE2 Hull 342, Twin Bed. OLLIE DIY’s: Timken Bearings, BB LiFePO4's, Victron 712 Smart, 350 Amp Master Switch, Houghton 3400, Victron Orion DC - DC, 3000-Watt Renogy Inverter, P.D. 60-amp Converter, Frig Dual Exhaust Fans, Kitchen Drawer Straps. Front Wardrobe Shelves, Snuggle Shelf. TV DIY’s: 2 5/16" Anderson System, Nitto recon’s, Firestone Rear Air Bags, Bilstein 5100’s, Mud Flaps & Weather Tech all, installed Ham Radio (WH6JPR).
jd1923 Posted 9 hours ago Posted 9 hours ago (edited) On 11/14/2026 at 1:15 PM, jd1923 said: So 4 AWG is too small for 50A but somehow 12 AWG works for 20A? Let me answer my own question with some simple ratios and extrapolation! Wire gauge is based on the cross-sectional area of the wire. First lets translate AWG into Metric for area measured in mm2: 12 AWG = 3.31 mm2 4 AWG = 21.15 mm2 1/0 AWG = 53.5 mm2 Area Ratios: 21.15 / 3.31 = 6.4 and 53.5 / 3.31 = 16.2 Hypothesis: a 12 AWG can power a 20A circuit. If so then 4 AWG can power 128A (6.4 x 20A) over the same distance. The conclusion is wrong since the premise is false (BS in, BS out). Let’s turns these numbers around. 50A / 6.4 = 7.8A which means if 4 AWG can power 50A then 12 AWG can ONLY handle 7.8A. Now were get closer to sanity. But, for those of you who believe 4 AWG cannot handle a 80 ft run for a 50A charger and that 1/0 AWG is the correct wire size, then the 12 AWG should ONLY handle 3A (50A / 16.2). The table copied above is more conservative than these numbers. A trickle charge is 1-2A. I will be adding a 2A trickle charger to our system soon. Certainly not to charge 900 Ah of house batteries, but to reverse charge the starter batteries to keep up with our router power requirements. I will install it on our 4 AWG DC-DC wiring, not the BLACK wire on the trailer harness. In our hull this wire will remain disconnected, terminated at the Oliver +bus. Edited 6 hours ago by jd1923 Chris & John in Prescott, AZ | 2016 EII #113 | '01 Ram 2500 Cummins!
ScottyGS Posted 8 hours ago Posted 8 hours ago I am so glad I have a good shop that is going to do this install for me and make sure everything is Okie Dokie..... 1 Gregg & Donna Scott and Missy the Westie - The Flying Sea Turtle - 2016 Hull # 145 2024 Nissan Titan XD - Western NC
jd1923 Posted 8 hours ago Posted 8 hours ago 14 hours ago, Geronimo John said: I believe that the charge wire is sized to provide code required charging of the Emergency Break-Away System. These are independent systems. With a hitch failure the 7-blade coupler is disconnected and the pin to the break-away is pulled out from the switch creating a closed circuit to the 4 magnetic brakes with power supplied by the trailer. In the Oliver and other TTs. the break-away switch is wired to the house batteries not the "charge wire" meaning the Black/AUX wire in the trailer harness. In flatbed or cargo trailers where there are no house batteries a small dedicated battery pack is installed for the sole purpose of powering the brakes in such emergency. Chris & John in Prescott, AZ | 2016 EII #113 | '01 Ram 2500 Cummins!
Geronimo John Posted 4 hours ago Posted 4 hours ago 3 hours ago, jd1923 said: In flatbed or cargo trailers where there are no house batteries a small dedicated battery pack is installed for the sole purpose of powering the brakes in such emergency. Bingo much better stated. I agree. If one has a trailer with an Emergency Break-Away system and a small small dedicated battery, where or how does it maintain it's charge? Where my brain failed me was thinking having such a charge wire from the TV is code required for ALL vehicles that have hitches. That's just not the case, so I appreicate your thougths. The TV charging wire (typically via a 7-way connector) is useful to keep an onboard breakaway battery topped off while towing, rather than being a universal requirement for every hitch-equipped vehicle. Back to the topic, this charge wire can NOT be directly connected between a TV (AGM or LA) and a trailer with Lithium house batteries for fear of the lithiums causing damage to the TV charging system and battery. Hence, when our owners upgrade from LA or AGM to Litho's, we take this wire out of service to prevent such a problem. This can be done in a way so as to have available the line for use by DC-DC charging shutdown feature. GJ TV: 2019 F-150 SuperCrew Lariat, 3.5L EcoBoost, 10 Speed Trans, Max Tow, FX-4, Rear Locker OLLIE: 2018 OE2 Hull 342, Twin Bed. OLLIE DIY’s: Timken Bearings, BB LiFePO4's, Victron 712 Smart, 350 Amp Master Switch, Houghton 3400, Victron Orion DC - DC, 3000-Watt Renogy Inverter, P.D. 60-amp Converter, Frig Dual Exhaust Fans, Kitchen Drawer Straps. Front Wardrobe Shelves, Snuggle Shelf. TV DIY’s: 2 5/16" Anderson System, Nitto recon’s, Firestone Rear Air Bags, Bilstein 5100’s, Mud Flaps & Weather Tech all, installed Ham Radio (WH6JPR).
jd1923 Posted 3 hours ago Posted 3 hours ago 1 hour ago, Geronimo John said: If one has a trailer with an Emergency Break-Away system and a small dedicated battery, where or how does it maintain its charge? Yep, they should be charged annually during off-season maintenance and replaced in so many years depending on the battery chemistry, no charger on board. In 40 years of trailering, I’ve always called the Black wire “AUX.” Never a “charging” wire! First 3 trailers we had, a horse trailer and two cargo trailers, the AUX wire powered the interior lighting of the trailer, no chargin’ happenin’! 🤣 Chris & John in Prescott, AZ | 2016 EII #113 | '01 Ram 2500 Cummins!
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now