Jump to content

Rear Bumper Pin (Right Side)


Imelda

Recommended Posts

All, I have had trouble getting the right side rear bumper pin in and out from when I got my Ollie last year.  The left one seems easier but I have to work hard with silicone grease, wiggling the bumper and a few added profanities to get the right side pin out on my Oliver 2020 Elite 2. The pin has to go through 4 holes with little clearance that have to line up perfectly to get the pin in or out.  I have seen a previous post where someone reported the same difficulty and one suggestion was to drill the bumper holes diameter a little larger. Anyone ever try this? Or are there any other suggestions like using a smaller diameter pin etc. 

Link to comment
Share on other sites

travel trailer units for sale
Find Oliver Travel Trailers for Sale
New Travel Trailers for Sale
  • Moderator+
17 minutes ago, Imelda said:

All, I have had trouble getting the right side rear bumper pin in and out from when I got my Ollie last year.  The left one seems easier but I have to work hard with silicone grease, wiggling the bumper and a few added profanities to get the right side pin out on my Oliver 2020 Elite 2. The pin has to go through 4 holes with little clearance that have to line up perfectly to get the pin in or out.  I have seen a previous post where someone reported the same difficulty and one suggestion was to drill the bumper holes diameter a little larger. Anyone ever try this? Or are there any other suggestions like using a smaller diameter pin etc. 

By far, the best and easiest way to fix this problem (many of us have had this through the years) is drill it out, I would start with the easy side locked in place and use the correct size bit (as determined from the opposite side) if that doesn’t fix the problem, go up to the next larger bit until it works, try not to go too much oversize to prevent “slop” in the fitment.

 

  • Like 3

Steve, Tali and our dog Rocky plus our beloved Storm, Lucy, Maggie and Reacher (all waiting at the Rainbow Bridge)

2008 Legacy Elite I - Outlaw Oliver, Hull #026 | 2014 Legacy Elite II - Outlaw Oliver, Hull #050 | 2022 Silverado High Country 3500HD SRW Diesel 4x4 

 

             801469912_StatesVisitedTaliandSteve08-23-2021-I.jpg.26814499292ab76ee55b889b69ad3ef0.jpg1226003278_StatesVisitedTaliandSteve08-23-2021-H.jpg.dc46129cb4967a7fd2531b16699e9e45.jpg

 

 

Link to comment
Share on other sites

Our pins which secure our bike rack to the bumper are a little tight as well, but a little wiggling of the bumper works. I don’t see a need to drill ours. 
 

 

2020 OLEII - Hull #634 aka-  “XPLOR”

2021 F350 6.7 liter Diesel Lariat Ultimate Tremor 

North Carolina 🇺🇸

 

IMG_2879.jpeg

Link to comment
Share on other sites

Drilling is very simple, just get a bit the same exact size as your pin, do NOT go larger! That is not needed and will just make things too loose, the tight fit is needed for the ball to work correctly… There may be a slight misalignment or burr, and a bit the exactly same size as the pin will clean that up nicely. make sure the other pin is installed and lift up very slightly on the bumper to center the holes. My pins are 3/8”, double check yours, but I expect that is correct. A 3/8” bit will be found in most basic drill bit sets. If you don’t already have one, this set is quite nice for emergencies and fits in a galley drawer neatly. I also carry a Dewalt cordless drill and 1/2” impact driver when travelling, but that may be too anal for you. 😬

If you drill the holes with that bit and the pin still doesn’t go in, then you should replace it. There is either something wrong with the ball detent or it might be bent. You could try straightening a bent one using a bench vise and mallet, but there isn’t much you can do if the ball is messed up.

John Davies

Spokane WA

359BAF21-DADB-4B33-B41B-B7494533F6F3.jpeg

  • Like 3

SOLD 07/23 "Mouse":  2017 Legacy Elite II Two Beds, Hull Number 218, See my HOW TO threads: 

Tow Vehicle: 2013 Land Cruiser 200, 32” LT tires, airbags, Safari snorkel, Maggiolina Grand Tour 360 Carbon RTT.

Link to comment
Share on other sites

I've had to do several things on my trailer to get them to work better, 1. lube the pin on the Anderson hitch will make a big difference in it's use, 2. drill out the pin holes on the rear bumper so the pins will go in and out with much more easy (John way is the proper way to do it), 3. file the side slide cut on the folding steps so the steps would slide properly, be surprised taking off a 100/1000's of a inch will do. I find that just about everything I buy these days needs a little tweaking to make it work correctly, I sometime wonder what people who are not mechanical minded do, use this forum and learn, good source for knowledge. 

trainman

  • Like 2

2019 RAM 1500, 5.7 Hemi, 4X4, Crew Cab, 5'7" bed, Towing Package, 3.92 Gears. Oliver was sold.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...