Search the Community

Carl - Another thing that you can try is to press down (towards the tire) on the TPMS while at the same time turning the TPMS anti-clockwise (lefty loosey). If the sensors aren't on too tight this just might work without that little wrench. One more - Hold the main body of your TPMS in your left hand and use your right hand to try to twist the very top of the TPMS (again anti-clockwise). Again, if the top isn't screwed on too tight, it just might come off without that little wrench. And, finally - if you have either a thin head adjustable wrench or a thin pair of pliers, you can use those in place of the little wrench. Be a bit careful doing this in that you certainly do not want to bugger up the relatively soft plastic that these TPMS housings are made out of. Bill

My Tire Minder TPMS sensors come with a nut that is tightened by the little wrench. If you try to unscrew the TPMS sensors without first loosening the nut with the little wrench and then spinning the nut toward the wheel, the TPMS sensors will not budge. This is a theft-deterrent measure--Tire Minder figures a casual thief won't have one of the little wrenches, but you will keep the one they supplied. If yours are Tire Minders, try loosening the nut first, then spinning it toward the wheel. A Tire Minder TPMS sensor will then twist off with just counterclockwise hand pressure.

What brand TPMS?

Greetings! I need to remove the TPMS transmitters to inflate the tires but I can't get them off. The little wrench they supplied does not do the trick. Any other suggestions? Carl

I have the Tire Minder TPMS system, with 4 sensors. Installing each of the 4 sensors caused the stem to leak, briefly, until I got the sensor screwed all the way into the stem. Then, the leakage stopped. This might be the simple answer to your query. But, if you they leak again, I recommend you submit a service ticket to Oliver. Oliver sent new "plug-resistant" tire valve stems, with $25 gift cards to cover some of the installation cost, to all those they knew of that ended up with balance beads in their tires when they picked them up from the factory. I was told, when we took delivery of Hull #1291 in November, that the balance beads had been removed from all of our tires. Maybe they missed your Hull # 1242, and maybe it has balance beads. If your leaks persist, Oliver should "make it right" by sending the right "bead-compatible" tire stems to you, or paying to have the balance beads removed from all of your tires, and new valve stems installed.

I take my TPMS devices off in the winter. When I install them in the spring there is a minute small air lose when they are seating on the valve stem. Are you sure you have a leak. Did you unscrew them to see if the air loose continues?

I just installed the TireMinder i10 on my 2022 Oliver which was straightforward enough; however now two of four tires have leaking (stuck) stem valves! I managed to screw all the transmitters on so the leaks are stopped and the tire pressure is at the planned 55 psi. Questions: Is this a common problem/result of installing this product? I assume I need to install (learn how to) some new valve stems and not some how fix? Any recommendations on brand or model for new stems? Install method advise? I have Cooper Tires "Discover HT3" tires as equipped by the factory. Thanks for any advise.

I just completed the mounting of our Tire Minder TPMS booster, following your excellent instructions and photos. I am pleased with the location of the booster and the relative ease of installation, relying on your post. Thanks for posting!

I bought the TST 507 tpms for both the LE2 and the TV. My reasoning for the tv sensors was that as I understand it, the vehicle sensors are for pressure only. I wanted to see the temperatures too. I bought a ViAir to air up the tires as needed. John

The EZTire TPMS (like this) also does not have to be rotating to read temp and pressure.. Bill

That's a significant advantage of your TSP TPMS! Something to verify before purchasing a TPMS for sure.

The TST TPMS we use monitors the tire pressure and tire heat and does not require the tire to be in rotation for a reading. It also works fine on the stationary spare. Patriot 🇺🇸

John, I have the TST TPMS and I replace the batteries in the sensors once per year. I also remove all batteries on any Ollie remotes when we winterize. Just replace with fresh in the Spring. Old batteries can weep and become a mess if left too long in any device. Patriot🇺🇸

I recall that putting our TPMS on spares was not an effective tire monitoring approach. Unless the tire is turning, it will not for most system report a pressure. If Ollie has a deflation, when I mount the spare, I transfer the sensor to the spare. That said, having spare sensors IS a good idea. So point well taken, just for our system, a different reason. GJ

It sure would be grand if Ford had a software upgrade for our "slightly used" F-150's to allow the onboard TPMS to be extended to our four OE2 tires.

I have an EEZTire TPMS like GJ above but since most of the more popular brands of these work in a similar fashion, I doubt that there are significant differences. I've found that I get about 2 years out of a set of batteries. However, when I have Twist stored I take the sensors off the tires, and, remove the batteries. I'm sure that Matt will be happy to hear from you. Bill

How often do you have to change out the batteries on your tpms? Our TST lasts a year according to the packaging directions. I wrote to Matt today. John

Bill, I have the ViAir air compressor which I plan to have with me. Initially I thought to get a couple extra for the spare tires, but if I should ever need to put the spare tire on, I figured that I could air up those spares and swap out the Tpms on the new tire. I think the batteries in those sensors only last a year. Might want to get eight batteries. John

The Tire Minder also has the ability to monitor both the tow vehicle and all four tires on the trailer. You just need to buy enough TPMS sensors for all 8 wheels.

I use the TireTracker TPMS system. Using the instruction manual, I found it very easy to program. My TV already had its own TPMS system so I added only the Ollie to the TireTracker system. For those without a TPMS on their TV, the TireTracker system has enough capability to add both the TV and the Ollie.

The Tire Minder TPMS system we recently purchased for the Elite II we picked up on November 10, 2022 was relatively easy to program. It performed well during our 2000+mile journey back to Idaho. With ambient temps ranging from the teens to the 50's F, we noted about a 3-PSI pressure increase from 50 PSI "cold" to 53 PSI "hot" as the tires warmed while on the road. It will be interesting to see what happens when towing in warmer temps, next spring.

I saw a number of responses concerning the rear view camera but nothing specific to the TPMS. I'd love to have a system that speaks to the truck instead of adding another device to the dash or trying to sync with my phone.

I have the Ford accessory trailer camera, but no Oliver yet. The camera comes with a wire harness the runs from the trailer camera to the video plug at the bumper. It will be a direct feed to the dash screen. This is a sample picture provided by Ford for the view on the dash from the Trailer cam: Ford also offers TPMS sensors for the trailer as well that integrate on the dash with the truck TPMS system. They can all be ordered in the same kit.

OLIVER HULL #1291 DELIVERY, INSPECTION AND WARRANTY SERVICE EXPERIENCE This very long post details our delivery, inspection and initial warranty service experience with our new Legacy Elite II travel trailer picked up on November 10, 2022. I begin with our overall impressions, for those who want just the “bottom line.” OVERALL IMPRESSIONS The Elite II is a quality trailer worth the price paid. We are glad we waited to get the Truma upgrade package including the AC, the CP Plus Varioheat wall control and the Varioheat furnace. Oliver does not lap seal all screw holes on the roof during production, but does lap seal as part of the first year’s annual maintenance. Oliver’s production staff continues to make some mistakes, but Oliver’s Service Department promptly and effectively addresses flaws for which service tickets are submitted. If you are interested in more detail, including how our delivery process went, the specific issues with our Hull #1291, and how they were resolved, keep reading. DELIVERY Ryan from Service did a generally good job with the delivery process. But, he failed to provide instructions for running the AC on battery power, which is one of the reasons we bought the Lithium Pro package. We had to figure out on our own that the AC remote must first be electronically paired with the CP Plus Varioheat wall control, and that the inverter must be switched on, or the AC unit will not be recognized by the CP Plus Varioheat wall control. Once we completed those steps, the AC worked well on inverted battery power. Our trailer has Goodyear Wrangler Workhorse LT tires mounted on 16” wheels. I was advised by Oliver Operations Manager Rodney Lomax that the ST tires on 15” wheels will not be installed on new trailers until March, 2023. I asked Ryan if the tires contained balance beads. He replied that after the balance bead/valve stem issue, Oliver determined to remove balance beads from all tires going forward, and leave them unbalanced. He asserted that trailer tires don’t need to be balanced. Jason Essary and Oliver Operations Manager Rodney Lomax also advised they are satisfied that trailer tires do not need balancing. Note Added After Towing 2000+ Miles Back to Idaho: I do not feel the need to get the trailer tires balanced. The trailer towed smoothly. SPECIFIC OBSERVATIONS ABOUT THE TRAILER Hull #1291 is the third trailer delivered with the new Truma package including Aventa AC, Varioheat furnace and CP-Plus integrated thermostat/control for heat/AC/water heater. We deferred our delivery from September to November 10 so we could get the Truma package in our 2022. #1291 is also the third trailer to get the Victron MPPT solar charge controller, which is standard with the 2023 solar package. I mistakenly presumed that since the Victron BMV-712 Smart Battery Monitor is mounted in the same place that the Zamp monitor was that it, too, reports solar panel charging data. It does not. It reports only the battery charge status. In trailers with both the solar and lithium packages, it is one of four ways to access battery charge data: (1) by reading the Smart Battery Monitor; (2) through the Lithionics app; (3) through the Victron Connect app and (4) by pressing “Batt” on the Seelevel monitor. Those who order wet cell or AGM batteries without a solar package have one way to check battery charge level: the Seelevel monitor. To check on solar charge data, there is only one option: you must access the Victron Connect App and click not on the Smart Battery Monitor icon, but on the Solar Charge Controller icon. You can then see real time solar charge data (if it’s night the charge data will be 0), and historical data for the past 30 days. The Truma AC is quiet. Although it produces 62 dB on high, the low and night settings logged in at 48 dB. It is easy to carry on a normal conversation at those levels. The Varioheat furnace includes much more substantial ducting than what I have seen in photos of Suburban furnace installs. It is not kinked or twisted, as some have reported with previous furnaces. Hull #1291 also includes a return air vent in the bathroom, which allows cold air to be returned to the furnace through the service area in the bottom of the trailer. This results in a much better balanced forced air heat system. Previous posters with the Suburban furnace noted that the “bilge” area under the street side bed where the external faucet is located stayed about 5 degrees above the outside ambient temperature on cold nights in the teens. We found that, with the Varioheat furnace set to heat the cabin to 70 degrees F, the “bilge” area stayed at 38 degrees F with outside temps at 11 degrees F. We did not then worry that the plumbing and tanks below the floor would freeze. The CP Plus Varioheat thermostat requires a learning curve, as it is not yet covered by any Oliver videos. It controls the Varioheat Furnace and the Aventa AC, as well as the Aquago water heater. AC control appears as an option on shore power, but not on battery power until the inverter is turned on. We were shown how to use it on shore power during the delivery process, but we were grateful that Oliver also provides a notebook containing owners manuals for the Truma products, as we had to study the owner’s manual later to really learn how to operate it, including when testing the AC on inverted battery power. The fit and finish inside and outside the trailer is improved over that reported by some on this forum. The interior caulking, such as in the shower, is nicely done. As an example, the plumbing vent hole in the closet is now sealed with a gasket, rather than just caulked (sometimes incompletely) as noted by earlier posts on this forum. INSPECTION AT DAVID CROCKETT STATE PARK From review of posts on this forum, I had compiled a long list of nearly 100 production defects noted by posters over the past several years. I spent most of the next 3 days at David Crockett State Park inspecting the trailer inside and out to determine if any of those defects were present in our trailer. None of those issues, ranging from improperly installed windows, to missing caulk around stabilizer jacks, to improper grounding of the inverter, were found in our trailer, save two: (1) there were no rubber plugs in the drum brake backing plates and (2) there was a roof leak. We found 5 significant issues, for which we submitted service tickets: 1. A leak appeared onto the standard bed area below the Truma Aventa air conditioner. It rained in Hohenwald the night we took delivery, then we found the leak the next day when we arrived at David Crockett State Park. As we had not used the AC, we suspected something on the roof needed to be resealed to prevent rainwater from penetrating the hull when on the road. This issue was on my list. 2. The Truma Aquago Antifreeze unit we purchased from Oliver did not yet communicate with the Truma CP Plus Varioheat wall control unit, so it could not be used. 3. The grey tank sensor gave erratic readings that did not correlate to water usage. 4. The bath fan vent and plumbing vent screws on the roof were not sealed, providing possible leak points; and 5. The one other item that was on my checklist: The drum brake backing pads do not have rubber plugs to protect the adjustment mechanism from road grit. When dumping the black and grey tanks before heading back to Hohenwald, the grey tank cable pull handle came out in my hand, preventing me from dumping the grey tank. When speaking with Mike Sharpe from Oliver Service, I also advised him of this issue that had come up that morning. RETURN VISIT TO HOHENWALD We delivered Hull #1291 to Oliver Service the late morning of Monday November 14, 2022. Later that afternoon, Jason Essary advised that his techs had verified the water leak and believed its origin was around the ventilation fan. They resealed that area, but then also applied sealant to all of the exposed screws on the roof (at no additional charge), because I had expressed concern that they were potential leak points. Operations and Sales manager Rodney Lomax advised that those screws are not sealed during production, but that the Service Department applies lap seal to them if annual maintenance is scheduled. I suggested that, like the screws that secure metal roofing to sheathing, those screws should be either gasketed or otherwise sealed as part of the manufacturing process. We were asked to leave the trailer overnight, so the sealant could cure before leak testing the next day. Because rain was forecast for that night, and because we asked to be able to sleep in the trailer, Operations Manager Rodney Lomax arranged for the trailer to be placed under a large awning/overhang at the Sales and Service facility to keep the roof dry. We noted when we slept in the trailer that night that all of the service ticket items had already been addressed except the water leak and the plugs for the drum brake backing plate. The grey water tank sensor was now reading consistently and the CP Plus wall unit was recognizing and controlling the antifreeze kit. The grey water tank pull handle had been reattached. [My later inspection suggested that the set screw, which secures the aluminum shaft (to which the grey tank drain handle is attached) to the guillotine valve under the street side bed, had come loose. I expect the handle with shaft simply needed to be reinserted and the set screw properly torqued.] We were advised that the brakes come from Dexter without plugs for the access holes, and Oliver does not supply them. So, I determined to cover the access holes with Gorilla tape until I could buy plugs online at home and install them. We yielded the trailer to the service team the next morning, expecting that after a leak test, we could be on our way home. But, we were advised a few hours later that when leak testing, it was discovered that our windows had not been installed according to a new protocol recently implemented by Oliver, so Jason had instructed his techs to pull and properly reinstall all windows, including re-caulking exterior flanges. That took the balance of the day. Jason and some of his staff stayed until after 6:00 p.m. that evening to complete the work and return the trailer to us, so we could camp another night at the Oliver campsite rather than find a motel. The process of addressing our multiple service tickets required us to hang out in Hohenwald for another two days, and delay our plans to return to Idaho. But, we had planned extra time for this purpose knowing that such a delay was possible. In total, we spent 6 days in Tennessee receiving delivery, inspecting and testing systems, and coordinating repairs. We appreciate Oliver lap sealing all of the screw heads and holes in the roof of our trailer, at no charge to us. We believe all Oliver trailers should have all roof screw holes lap sealed as part of the production process. Had that been done to our trailer before we took delivery, it would have saved us a day in Hohenwald. We also appreciate the Oliver service team for promptly addressing our service tickets right after we arrived back at their facility, and, even though it took an extra day, for ensuring that the windows were properly resealed though we had noted no issues with the windows. It is a concern that Oliver’s production staff overlooked the items for which we submitted service tickets during construction, and failed to follow the new protocol for window installation when building our trailer. But, we left (two days later than we had originally hoped) with what we believe is a high quality trailer that is worth the premium we paid for it. And we left with great respect for the integrity and commitment to quality of the Oliver service and management team. HELPFUL THINGS LEARNED FROM FORUM POSTERS I learned many things from posters on this forum which have made using the trailer much easier and safer. These include: Inserting turnbuckles into the chains of the Andersen WD hitch, with the extra chain links required to fit the Elite II. This has made it easier to attach and detach the Andersen by turning the turnbuckles to create slack. It also makes it much easier to get the “whale tail” back on if it was detached at an angle—just loosen the turnbuckle on the long side even more, and the whale tail can be installed at an angle. Then, of course, tighten the turnbuckles to tension the WD hitch. I use Robogrips to complete the tightening process. This is much easier for an old guy than crawling under the trailer to loosen the nut with the Andersen provided socket. Using a Camco water filter and a brass hose elbow when hooking up city water Installing a dash cam Using a PUR water filter pitcher Installing a Tire Minder TPMS system Using a squeegee to wipe down shower walls Installing X-Chocks between the wheels on the two axles. If you posted about these items, THANK YOU!

SeaDawg: Excellent advice! Beaver Pilot: Please post your TV and OTT info in your signature line. I have three close friends, all life-long residents of AK, who basically advised us the same concerns posted by SeaDawg. This past summer, we spent 45 days in Alaska with our OEII, most of it boondocking. However we did not venture very far north of Fairbanks. Over 15K from TX out and back. You'll need to be prepared for a lot of flying missiles and very rough slow slogging roads heading your way, especially if you venture more than very far from Fairbanks. As an Alaska Bush pilot, you likely have all of the below. But for new owners who have not DRIVEN to AK, here is a list of items that I found appropriate: Searching "mud flaps" and "stone stompers" postings at our forum. Start by looking at the bottom of all of John Davies post where he has a link to several of them. He, and other owners have well documented DYI solutions that such a trip would warrant. One suggestion that I did not take, that I wish I had done, was padding the front edges of my OEII and rear mud flaps on Ollie. Got battle scars as a result. Bringing a full compliment of tire maintenance tools (TPMS, Air Gauge, Air Compressor, jack, and a tire plug kit is the minimum. Bring an RV satellite based navigation system/ I have, and recommend, a Garmin InReach Mini II. If you don't have Ford's 36 gallon fuel tank (or equivalent), then having extra fuel cans. If your TV is older, then consider rubber hoses and belts. Handy to have a spare engine oil filter and oil. Near perfect full size spares for both TV and Ollie. Vehicle recovery gear. Good set of tools. First aid kit and extra meds for the duration of your trip (No Resupply). Update your Ollie with outdoor bug lights (courtesy (puddle) lights and porch lights). Finally if going way north of Fairbanks, plan on replacing your windshield and likely your Oliver front logo when you get back. Please keep us posted, and when you get back, kindly update the above list with your thoughts and experience. Good luck and safe travels! Geronimo John