ScubaRx

I was thrilled with the news that they were actually rated at 2750 pounds. I had abandoned the idea of buying them if they were only rated at 2000-2400 pounds. I will continue to run 50 psi in my tires. With a rating of only 10.4K pounds the axles are now the weakest link in our entire suspension/wheel/tire system.

The Outlaw Oliver now has 4 new five leaf Alcan Springs, 4 new Monroe 555001 Shocks and 4 new Hercules H-901 Commercial Light Truck tires. Tali and I installed the springs and shocks earlier this week and the new tires went on yesterday. Our next trip will likely be 10K miles over the next three months or so. I believe we are good to go now. We will leave Monday for the Rally in AL, then on to the Rally in ME and from there to CO for a few weeks. We hope to hit a few more National Park Units. As of December 2023, there are 429 official units of the National Park System, We've visited almost 300 so far.

One of the former owners sold his Oliver, bought a Super-C and a Jeep to pull behind it, sold that and ordered an LV. It took nearly two years to get it and cost around $500k. They require you to have a one ton truck before they will sell you one. His weighed 18,000 pounds.

I have often successfully used super glue and baking soda to fill a hole in plastic. It will solidify into a substance that you can mill, drill, sand ect. Fill and pack the existing hole with baking soda. Put a few drops of super glue on top and let it soak in. It will shrink down somewhat as it hardens. Fill again until flush with the top of the old hole. Use a file or sand paper to obtain a flat surface. Find the center and drill the new hole. This stuff is really hard when cured and won't expand much. If you drill the hole too small it will shatter when you put the screw in. Do a couple of practice runs on something else before you try to repair the blind. If you get it right, I've never had one to fail.

Tali and I have been around and under the trailer all day installing the new Alcan springs. While under there, I counted eight cross members behind the rear axle with one doubled.

No, but originally there were only four. Like mine, the belly behind the axles started to sag and more were added. Yours was likely repaired prior to your acquisition. You are correct that the frame's were shorter and the bumpers were almost flush with the back of the hull when the first two 22 footers were built in 2008-2009. They were likely done this way because that's the way the 17 foot Elite rear storage area had been designed. In 2014, after the hiatus, the decision was made to lengthen the frame on both the models. This was done for looks and since there was no other fiberglass travel trailer this big it made for good marketing. The length of a travel trailer is defined by the distance from the tip of the hitch to the back of the bumper, so the 17 foot Elite became 18.5 feet long and the 22 footer became 23.5 feet long and was finally given an official name, becoming the Elite II. Even though the rear of the frame was lengthened by 1.5 feet the number of cross members remained the same as before. This 22 foot trailer were built during late 2008 and early 2009 although it was not sold right away. Another unit was built for Jim Oliver and it was completed. He named it "The beast". A third unit was planned but the company decided to shutter the trailer line and it was never started. Here are a few construction pictures taken during that time period. Some were taken by myself and some by Robert Partee, the sales manager at the time. Here you can plainly see the frame rails extending far beyond the rear of the body and the cross members welded below the belly.

Jim Oliver told me personally that the frame was designed to handle up to 3X the GVWR. He quoted the number at 21K pounds. I do know that the number of rear cross members is now twice those of the three 22 footers that were built in 2010 (that was what the Elite II’s were called back then.)

It could be done. You would want make sure to use a polarized plug so that the positive and negative can’t be reversed. It might not even matter, depending on what you plan to use it for.

@MAX Burner & @Patriot My bike was not quite as fancy as the ones you guys ride. But, when you're 15 years old, in the 10th grade and all the senior cheerleaders are begging you to take them riding on Saturday and Sunday afternoons, it was pretty cool. Hang on tight, baby...

I would pick a location where you want the freezer to sit and install one of these near it. You would probably want to run a new power line from the distribution center under the dinette to power only this receptacle. You can pick up the negative side from the buss bar under the aft dinette seat. You'll need a 1-1/8" hole saw to cut the mounting hole.

The negative side should run through the shunt rather than to the batteries.

Is the girl standard or optional?

This is why I preach always use blocks under all three jacks. The service team should alway place a six inch block under the front jack foot when readying a trailer for pick-up.

Forum is alive and kicking @ 0243 on 04-27-2024.

I suppose other parts of the country must have grid problems much more often than our neck of the woods. I've lived within 20 miles of where I live currently for greater than the last 7 decades. Our power comes from TVA and has for almost 100 years. Tupelo was the first TVA city starting in the early 1930's. At least in my lifetime that grid has never failed. I've lived in this house for over 40 years and I can remember only twice the power went out. Once during a severe ice storm in 1994 and again in 2014 after an EF3 tornado that we missed because we were traveling.

Well, most of us do. We've already racked up over 6K miles since the middle of January with our yearly trip to Quartzsite and then back to Texas for the Eclipse. Next are two Oliver rally's back to back and then out to Colorado and back. Probably another 12-15K miles over the next 3-4 months. We've seen two car haulers full of those cyber trucks in the last few months. I still think they are butt ugly.

It looks a bit like a dumpster.

Wow, that's 24 amps/day, for nothing. I was unaware of this. So, apparently there's no way to actually turn the inverter completely off?

That’s good. It helps keep the value of our existing trailers up.

My new springs should be here next week. That will make The Outlaw Oliver the oldest trailer to have them retrofitted to. I am excited to get them and although I've never had a problem with my original 5-leaf springs that came with the 5200 pound axles, I'm super confident that the new stronger Alcan springs will be much better.

I have sprayed ours regularly through the years. I've used WD-40 (messy) and dry silicone lubricant (much better). Aluminum tends to want to "stick" to itself. I've not thought about using paraffin, but that is a good idea. It might stay on longer than my methods. Give it a shot and let's see how it works.

Around 50psi.

I did, Lew (the owner) stated the person that wrote the email simply was mistaken.

I'd unhook from the water there until the plumber is long gone. You don't want contaminated water from where they worked on the lines to get into your system. Another reason to use from your own water tank when the other choices are questionable.

I'm unclear why you would think that. Your wheels have you at 7.8K pounds, well above the stated 7K GVWR. Which tires, axles and spring packs are riding under your Hull #045? How much does your trailer weigh full of water, gear and ready to camp for a 3 month long foray? The wheels and tires under my Hull #050 have a load rating of just over 13K pounds. The Axles are rated at 10.4K pounds. The Alcan springs can support 11K pounds. The Outlaw Oliver has always weighed well over 7000 pounds in its natural habitat. And, it has traveled over 100K miles, most of it with the tires sitting at 80psi all without a single issue. I'll be forever grateful for Jim Oliver's guidance and assistance in designing the most over built Oliver rolling down the road. But, there are those here that think I tend to over-engineer everything.